Bilge Pump Brkt Side Mnt
Side Mount Bracket (Rule)
- For 360, 500 and 1100 Pumps
- Allows for side mounting to vertical stringer, bulkhead or transom.
- Use when bottom-strainer mounting is inconvenient or impossible.
- Simply remove strainer, place in bracket and reassemble.
- Pump nozzle may point in any of three directions.
Bilge Water Alarm Panel
Bilge Pump Water Alarm Panel (SeaDog)
- Injected Molded ABS
- Provides an audible and visual means of warning the water level in your bilge is beyond your bilge pump float switch level.
- Bilge pump should be hooked up to a switch such as Sea-Dog part numbers 423030, 423040 and 423046.
- Rated: 15 Amps.
- A: 2-7/16"
- B: 3"
- C: 1-3/4"
- D: 2-1/2"
Bilge Pump Switch Automatic
Bilge Pump Float Switch (Boating Accessories)
- Automatic Float Switch (JOHNSON PUMP)
- This automatic switch has a time-proven micro switch without mercury.
- When water exceeds the acceptable level, the pump is turned on by a rolling steel ball, which changes the pressure on the micro switch.
- Attaches to any Johnson Pump bilge pump through the clip on "T-slot" and can be used with any 6, 12, 24 or 32 V systems.
Hand Bilge Pump 18" Length x 20" Hose
Hand Bilge Pump (SeaSense)
- 18" Length x 20" Hose
- Designed in conjunction with the agricultural industry for large scale water removal
- Same design has been scaled down for evacuating small boats, canoes, kayaks, bilges or any place water collects
- Anti-leak design
- Removable hose for easy storage
- Self-priming
- Reaches small, compact areas with ease
- Light weight
- Corrosion resistant
- A: Large economic, easy grip, high impact handle
- B: Tube cap. Caps the tube and forces the water out of the outlet and also supports the plunger shaft
- C: Plunger spacer keeps the shaft from coming up too far and damaging the plunger washer
- D: Plunger washer forces water up and thru the outlet
- E: Intake foot filters water coming in. Screws off for easy cleaning
- F: Washer seal eliminates any leaking from the top of the pump
- G: Outlet features improved threads for a more secure hold on the hose and eliminates leaking
- H: Corrosion proof plastic construction
- I: Plunger stop supports plunger washer when being pulled up allowing better water flow
Bilge Pump 12V 360 GPH
Rule 360 GPH 12V Bilge Pump
- Higher Flow optimized impeller to provide greater flow at the same amperage
- Built-in Thermal Cut-Off (TCO) provides added protection for pump and vessel
- Back Flow Prevention reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner
- Hidden Air Vents in the Body helps prevent air locking in challenging plumbing installations and helps with the check valve
- Threaded Discharge easier installation, easier maintenance
Bilge Pump Cartridge 500GPH
Bilge Pump (Johnson Pump)
- 500 GPH
- Cartridge F
- Replacement Motor Cartridges
- Replacement motor cartridge for select bilge, bait & wash-down pumps.
Hand Bilge Pump 24" Length x 36" Hose
Hand Bilge Pump (SeaSense)
- 24" Length x 36" Hose
- Self-priming hand pump was designed in conjunction with the agricultural industry for large scale water removal
- This same design has been scaled down for evacuating small boats, canoes, kayaks, bilges or any place water collects
- Anit-leak design
- Removable hose for easy storage
- Self-priming
- Reaches small, compact areas with ease
- Light weight
- Corrosion resistant
- A: Large economic, easy grip, high impact handle
- B: Tube cap. Caps the tube and forces the water out of the outlet and also supports the plunger shaft
- C: Plunger spacer keeps the shaft from coming up too far and damaging the plunger washer
- D: Plunger washer forces water up and thru the outlet
- E: Intake foot filters water coming in. Screws off for easy cleaning
- F: Washer seal eliminates any leaking from the top of the pump
- G: Outlet features improved threads for a more secure hold on the hose and eliminates leaking
- H: Corrosion proof plastic construction
- I: Plunger stop supports plunger washer when being pulled up allowing better water flow
BILGEKOTE WHITE QUART
BILGEKOTE WHITE- QUART NOT FOR RESALE IN CANADA
Bilgekote is an Interlux Paint. Hard wearing coating for bilges and bulkheads. Chemical resistance to fumes, fuel, and oil. High opacity for thorough coverage. Cleans easily for reduced upkeep.
Hand Bilge Pump 24" Length x 72" Hose
Hand Bilge Pump (SeaSense)
- 24" Length x 72" Hose
- Our self-priming hand pump was designed in conjunction with the agricultural industry for large scale water removal
- This same design has been scaled down for evacuating small boats, canoes, kayaks, bilges or any place water collects
- Anti-leak design
- Removable hose for easy storage
- Self-priming
- Reaches small, compact areas with ease
- Light weight
- Corrosion resistant
- A: Large economic, easy grip, high impact handle
- B: Tube cap. Caps the tube and forces the water out of the outlet and also supports the plunger shaft
- C: Plunger spacer keeps the shaft from coming up too far and damaging the plunger washer
- D: Plunger washer forces water up and thru the outlet
- E: Intake foot filters water coming in. Screws off for easy cleaning
- F: Washer seal eliminates any leaking from the top of the pump
- G: Outlet features improved threads for a more secure hold on the hose and eliminates leaking
- H: Corrosion proof plastic construction
- I: Plunger stop supports plunger washer when being pulled up allowing better water flow
Hand Bilge Pump 36" Length x 36" Hose
Hand Bilge Pump (SeaSense)
- 36" Length x 36" Hose
- Our self-priming hand pump was designed in conjunction with the agricultural industry for large scale water removal
- This same design has been scaled down for evacuating small boats, canoes, kayaks, bilges or any place water collects
- Anti-leak design
- Removable hose for easy storage
- Self-priming
- Reaches small, compact areas with ease
- Light weight
- Corrosion resistant
- A: Large economic, easy grip, high impact handle
- B: Tube cap. Caps the tube and forces the water out of the outlet and also supports the plunger shaft
- C: Plunger spacer keeps the shaft from coming up too far and damaging the plunger washer
- D: Plunger washer forces water up and thru the outlet
- E: Intake foot filters water coming in. Screws off for easy cleaning
- F: Washer seal eliminates any leaking from the top of the pump
- G: Outlet features improved threads for a more secure hold on the hose and eliminates leaking
- H: Corrosion proof plastic construction
- I: Plunger stop supports plunger washer when being pulled up allowing better water flow
Bilge Pump Cartridge 750GPH
Bilge Pump (Johnson Pump)
- 750 GPH
- Cartridge F
- Replacement Motor Cartridges
- Replacement motor cartridge for select bilge, bait & wash-down pumps.
Bilge Pump 500GPH 12V
Rule 25DA 500 GPH 12V 1.6 Amp Submersible Bilge PumpOur bilge pumps provide ultimate pumping performance, which helps keep your bilge clear of nuisance water, building on the genuine Rule design. Rigorous engineering and testing helped generate the DA series of bilge pumps. Our pumps are tested to the highest standard, achieving rated performance at 12V vs. 13.6V, resulting in higher flow with better efficiency for the toughest applications.
- Higher Flow optimized impeller to provide greater flow at the same amperage
- Built-in Thermal Cut-Off (TCO) provides added protection for pump and vessel
- Back Flow Prevention reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner
- Hidden Air Vents in the Body helps prevent air locking in challenging plumbing installations and helps with the check valve
- Threaded Discharge easier installation, easier maintenance
Bilge Water Alarm 2 1/2 x 4 1/2
Bilge Water Alarm Panel w/Pump Switch (SeaDog)
- Injection Molded ABS
- Provides an audible and visual means of warning that water level in your bilge is beyond your bilge pump float switch level.
- No need for separate bilge pump switch as the control switch selects between automatic and manual function of the bilge pump.
- Rated: 15 Amps.
- NOT FOR USE WITH PUMPS THAT HAVE BUILT-IN SWITCHES.
- A: 2-7/16"
- B: 4-1/2"
- C: 1-3/4"
- D: 4"
Rule Rule-a-matic Bilge Auto Switch W/O Fuse
Rule-a-Matic Bilge Pump Float Switch (Rule)
- Mercury
- Now includes a removable base for easy cleaning and servicing, a mercury free snap switch tested to over one million cycles and marine grade "blocked" wire.
- Designed for pumps drawing up to 14 Amps.
- Model 35A and 35FA now includes a 2 year warranty.
Bilge Pump Cartridge 1000GPH
Bilge Pump (Johnson Pump)
- 1000 GPH
- Cartridge F
- Replacement Motor Cartirdges
- Replacement motor cartridge for select bilge, bait & wash-down pumps.
Bilge Pump Cartridge 1250G
Bilge Pump Cartidge (Johnson Pump)
- 1250 GPH
- 12 volt
- Submersible
- Universal replacement for all Johnson Pump and Mayfair cartridge bilge pumps and cartridge baitwell pumps
- High-efficiency, durable and longlasting motor; ignition protected
Repl Mnt Module 700
Bilge Pump (Rule)
- 700 GPH
- Replacement motors for older style Rule Cartridge Bilge and Livewell/Baitwell pumps
- Features low amp draw, miniaturized to fit restricted areas, permanent magnet motor, stainless steel shaft, and an ultrasonically welded housing
Bilge Pump 800 GPH
Bilge Pump (Rule)
- 12 Volt
- 800 GPH
- Square
- Submersible
- 3/4" hose barb
- Designed for smaller boats.
- The square model features 36 mounting variations as well as a gas resistant stainer base.
- Easy installation, nylon impeller, stainless steel shaft and replaceable power module.
Bilge Switch W/O Fuse Rule-A-Mat
Rule-a-Matic Bilge Pump Switch (Rule)
- Dimensions: 3" x 5-3/8" x 2-1/2"
- Sleek and rugged, the Rule-a-Matic plus float switch has a strong, fully integrated and impact resistant cover, which protects against debris and jamming
- 14 gauge highly abrasive resistant marine grade wire, with a built-in test feature
- Designed for pumps drawing up to 20 amps
Rule-A-Matic Switch W/FuSE
Rule Rule-A-Matic Plus Float SwitchThe Rule-A-Matic Plus float switch has a strong, fully integrated and impact resistant cover to protect against debris and jamming, abrasive resistant marine grade wire, and a built-in test feature. 2-Year limited warranty.
Bilge Pump 1000 GPH 12V
Bilge Pump (Rule)
- 12 Volt
- 1000 GPH
- Submersible
- 1-1/8" hose barb
- Old 800 # 20
- Designed for smaller boats.
- The square model features 36 mounting variations as well as a gas resistant stainer base.
- Easy installation, nylon impeller, stainless steel shaft and replaceable power module.
Bilge Pump 800 GPH 12V Round
Rule 20DA 800 GPH 12V 3.4 Amp Submersible Bilge PumpOur bilge pumps provide ultimate pumping performance, which helps keep your bilge clear of nuisance water, building on the genuine Rule design. Rigorous engineering and testing helped generate the DA series of bilge pumps. Our pumps are tested to the highest standard, achieving rated performance at 12V vs. 13.6V, resulting in higher flow with better efficiency for the toughest applications.
- Higher Flow optimized impeller to provide greater flow at the same amperage
- Built-in Thermal Cut-Off (TCO) provides added protection for pump and vessel
- Back Flow Prevention reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner
- Hidden Air Vents in the Body helps prevent air locking in challenging plumbing installations and helps with the check valve
- Threaded Discharge easier installation, easier maintenance
Bilge Pump 900Gph Low Profile
Rule LP900D LoPro Low Profile 900 GPH Standard Bilge PumpLoPro™ LP900D Bilge Pump is a low profile pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4". It features a threaded discharge nozzle to which you can attach either the included straight or 90° fitting. It also iincludes a tricuspid check valve for the straight fitting which can be used to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose can also swivel 360° for better routing.
LoPro™ LP900S has two automated settings, enabling the pump to turn on when the water reaches either 1" or 1-3/4". In addition, the electronic automatic mode allows the pump to check for water every 2-1/2 minutes. If water is detected, the pump stays on until the water is removed. If no water is detected, then the pump turns off.
Bilge Pump 1100GPH 12v
Bilge Pump (Rule)
- 1100 GPH
- 12 Volt
- Port Type: 1"
- 4-3/8" H x 2-7/8" W
- Round
- Manual
- High-Flow
- Provides outstanding quality and value.
- Designed for small boats.
Bilge Pump 500GPH Rule Mate
Bilge Pump (Rule-Mate)
- Automatic
- 500 GPH
- No float switch required
- Features a solid state water sensing technology that eliminates the need for a separate float switch
- Pump turns on when water level rises and shuts off when water is removed
- Will not pump oil-straight motor oil that enters the bilge will not turn the pump on
- Snap-off strainer for easy cleaning
- Anti-fouling impeller
- For 19mm bore hose
- 114mm H x 152mm L x 83mm W
- 3 amp
- Up to 7 gal/min. Max recommended discharge head 2m.
- Compact pump for smaller vessels
- Tough plastic body
- Quick release intel strainer allows for rapid cleaning
- Low am draw conserves batteries
Bilge Pump Auto 500GPH
Bilge Pump (Attwood)
- 500 GPH
- 12 Volts DC Pumps
- Sahara bilge pumps include 36" lengths of 16-gauge tinned copper wire
- Wire is caulked to prevent water from wicking through insulation jacket
- All materials and components are state-of-the-art
- Permanent-magnet motor, stainless steel shaft, and steel-reinforced seal ensure powerful, durable performance
Bilge Pump 500GPH Auto
Rule 25SA 12V 500 GPH 1.9 Amp Automatic Bilge PumpIgnition protected. Double insulated long stack motor. Double strainer non-clogging protection. Compact, efficient and maintenance free. Totally submersible. Runs 100° cooler. No burn-out when dry. Moisture tight PTFE seals. Silent running. Vibrationless. Anti-airlock feature. Housing of heat resistant acetal resin. Heavy 5/16" stainless steel shaft. Nylon/fiberglass impeller for strength.
Bilge Pump 900 Gph Auto Low Prof
Rule LP900S LoPro Low Profile 900GPH Automatic Bilge PumpLoPro™ LP900D Bilge Pump is a low profile pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4". It features a threaded discharge nozzle to which you can attach either the included straight or 90° fitting. It also iincludes a tricuspid check valve for the straight fitting which can be used to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose can also swivel 360° for better routing.
LoPro™ LP900S has two automated settings, enabling the pump to turn on when the water reaches either 1" or 1-3/4". In addition, the electronic automatic mode allows the pump to check for water every 2-1/2 minutes. If water is detected, the pump stays on until the water is removed. If no water is detected, then the pump turns off.
Bilgekote gallon
Bilgekote Enamel
- Interlux
- Fast-drying, durable coating formulated for application to bilge areas
- Helps prevent absorption of oil, gasoline or sludge into wood and fiberglass
- Can be used to protect lockers and bulkheads from moisture penetration
- Resistant to chemicals, fuel, oil and fumes
- Cleans easily for reduced maintenance
- Considerable application covering due to the paints high density
- Hard-wearing coating for bulkheads
- Type: One-part enamel
- Finish: Semi-gloss
- Components: 1
- Solids by Vol.: 44%
- Coverage: 450sq.ft/gal.
- VOC: 414g/l
Bilge Pump 750GPH, Rule Mate
Bilge Pump (Rule-Mate)
- All-in-one pump & switch (no float switch required)
- Automatic
- 750 GPH
- Submersible
- 12 volt DC bilge pump preferred by yachtsmen and commercial fishermen worldwide.
- Features a solid state water sensing technology that eliminates the need for a separate float switch. E
-Easy clean snap lock strainer, anti-fouling impeller.
- When water enters the bilge and reaches a certain height (2-3/4 inches) a sensor turns the pump on. After the water is pumped out, another sensor shuts the pump off.(On 2-3/4”; Off 1/2”)
- Amp Draw @ 12.0 Volts: 2.7
- Amp Draw @ 13.6 Volts: 3.1
- Fuse Size: 5 amps
- Connections: one straight and one angle Hose barb fitting.
- Discharge Opening: 3/4”
- Discharge Finish: Barbed
- Housing Material: ABS
- Strainer Material: ABS
- Impeller Material: Nylon
- Shaft Material: Stainless
- Seal Material: Nitrile/Teflon
- Temperature Limit: 200 ºF
- Fluid Capabilities: Bilge Water
- Typical Life: 1500 hours
- Shut-Off, (0 GPM): 12'
- Footprint: 2.75" x 4.5"
- Wire Length: 29"
- Wire Gauge: 16 AWG
- Certifications: ISO 8846, ISO 10133, CE Certified EN50081-1 & EN50082-1, UPC Code 042237-111081